赛尔奇K30磨吸一体机

一、产品描述
Product Description 
1、该机本身包容1台吸尘器（一体不可分开使用），磨削吸尘一体化，做到无尘施工。
The machine includes a vacuum cleaner(can not use alone ).One machine can have two function:grind the floor and collect dust at the same time. 

2、该机配备不同性能的特种刀具，可实现研磨、切削两种功能，可适用不同地基表面的处理，如树脂涂膜的切削去除、凹凸地面的修整和打毛、除去浮浆、除去雨淋、塑料PVC地面及沥青黏结剂的翻新等。
L380 includes special cutting tools with different functions which means it can grind and cut.It can be used in different foundation surfaces,such as grind the resin paints, Trim the uneven ground, remove the slurry, remove the rain, renew the plastic PVC floor and renew pitch adhesive.

3、刀具为金刚石材质可针对新（老）地面，水磨石，**地坪进行研磨拉毛处理。正常情况下，研磨刀具处理标准混凝土地面约150-200M2/H左右，耗材成本约0.10元/M2左右。
Cutting tools are diamond material can be used for the new (old) ground, terrazzo and wear-resistant floor for grinding. Normally, the tool’s working efficiency when it is used in standard concrete floor is about 150-200㎡/h, which means just about 0.12 Yuan/㎡.

4、切削刀具为烧结金刚经特殊工艺处理而成的切削**刀具。主要针对1MM以下旧环氧、油漆、胶水、橡胶、油污等地面进行切削处理。
Cutting tool are special tool made by special fabrication processing. ?it was aimed?at?smaller than 1 millimeter old epoxy, paint, glue, rubber, oil and other ground.

5、技术良好，低**设计，提高了高负荷作业时的操作稳定性。同时，因机身小巧，故不受施工场地大小的限制。
K30 is lead in technology with low gravity design, improved operation stability during high load operation. Meanwhile, due to its compact size, it is not limited by the size of the construction site.

6、较低的故障率，可24小时连续施工。
The machine’s failure rate is very low. 24?hours?of?continuous?construction 

二、产品优点：
    Product Advantages:
1、机身小巧，扶手可以折叠，减小运输尺寸。
The size of the machine is small, the handle is collapsible. Decrease the transportation size.

2、打磨，吸尘一体化，做到无尘操作，噪音小。
Grind and collect dust can be done at the same time, the noise is low.

3、通过换刀具可以做到研磨的和切削。
Grind and cut can be realized by chaning cutting tools.

4、各部件之间有减震垫，减小机器的震动，增加操作的舒适度。
   There are cushions between the parts, which can reduce the vibration?of?this?machine and enhance operator comfort.

5、带有漏电保护，可以确保施工人员的安全防护。
With leakage protection, the safety protection of the construction personnel can be ensured.

6、刀头浮动，可以打磨，切削到比较洼的地方。
The head float, so the machine can polish the more hollow place.

7、带有转向倒顺开关.转向不对，只需拨动开关即可变换旋转方向。
   With a steering reverse switch. When the machine turn to the wrong direction, the operator can change the rotation direction by just press the switch.

技术参数：
型号	Model	K30
尺寸（全长*全宽*全高）	Size（L*W*H）	1200×400×896mm
总重量	Gross Weight	103kg
磨削宽度	Working Width	300mm
电机	Motor	3.7KW×4P（5.0PS）
电源	Power Supply	380V×9.**

一体式吸尘机规格	Vacuum Cleaner Specification
输出功率	Output Power	1.0KW
较大风量	Maximum Air Volume	3.0m3/min
集尘箱容量	DustCollector Capacity	15L
额定电压	Rated Voltage	220V
额定电流	Rated Current	**
电源线长度	Length of Wire	20m